• Outdoors do not apply under threat of rain.
• Surface, air and material temperatures should be 45of to 110of during application.
• Do not clean up the surface with acid products.
• Always apply at least two coats for best results.
• Test a small area of surface to ensure adhesion and desired results.
• Protect plant life and surfaces to remain uncoated. Use masking or drop cloths as required.
• All Joints sealant work must be completed prior to application SA-1099.

• Avoid contact with eyes, skin and clothing. Wash thoroughly after handling with water.
• Use appropriate eye wear and protective clothing.
• Avoid breathing vapors or mist.Use adequate ventilation.
• Do not expose containers at 150°F or higher.
• Keep away from heat or open flame.
• Do not expose containers at 95of or higher.
• Protect plants and vehicles from overspray.
• Avoid contact with all food stuffs.
• Keep container closed tightly when not in use.
• In case of ingestion, call hospital, physician and get medical attention.
• Keep out of reach of children.

The SA-1088 Coverage rates will vary greatly with the porosity of the substrate and the number of coats.
The gloss and finish of the surface will increase with every coat.
Porous substrates .................. 4 -6 m2 /l (200-250sq ft/gal) - 2 Coats.
Low porosity substrates ......... 6-8 m² /l (250-330sq ft/gal). - 2 Coats

Not recommended to apply over asphalt surfaces, plastic or continuous water immersion substrates.

We Warrants these products to be free of defects by use high quality materials. We Guarantee SA- 1088 and, when used as instructed, will provide great protection and prevent moisture and contaminant penetration. No warranty is effective with a deficient coating system or applicator.

• Weather shall be clear. There shall be no precipitation during and after application.
• Surface, air and material temperatures should be 45ºF to 110ºF during application.
• Do not clean up the surface with acid products.
• Always apply at least two coats for best results.
• Test a small area of surface to ensure adhesion and desired results.
• Protect plant life and surfaces to remain uncoated. Use masking or drop cloths as required.
• Joints sealant work must be completed prior to application SA-1099.

• Avoid contact with eyes, skin and clothing. Wash thoroughly after handling with water.
• Use appropriate eye wear and protective clothing.
• Avoid breathing vapors or mist.Use adequate ventilation.
• Do not expose containers at 150°F or higher.
• Protect plants and vehicles from overspray.
• Avoid contact with all food stuffs.
• Keep container closed tightly when not in use.
• In case of ingestion, call hospital, physician and get medical attention.
• Keep out of reach of children.

The SA-1099 coverage rates will vary greatly with the porosity of the substrate and the number of coats.
The gloss and finish of the surface will increase with every coat.
Porous substrates .................. 4-6 m² /l (200-250sq ft/gal).
Low porosity substrates ......... 6-8 m² /l (250-330sq ft/gal).

Not recommended to apply over asphalt surfaces, plastic or continuous water immersion substrates.

We Warrants these products to be free of defects by use high quality materials. We Guarantee SA- 1099 and, when used as instructed, will provide great protection and prevent moisture and contaminant penetration. No warranty is effective with a deficient coating system or applicator.

• Outdoors do not apply under threat of rain.
• Do not use acids for cleaning the already sealed surface.
• Apply SA-2099 to temperatures above 45 F.
• For best results always apply two minimal layers.
• All joints must be sealed before the SA-2099 impregnation.
• Pre-testing is recommended to ensure compatibility and adhesion.

• Protect containers from temperatures above 105 F.
• Non-flammable material, even if you try to apply in a ventilated place. Avoid inhalation.
• Avoid contact with skin and eyes, if it happens wash with plenty water.
• If ingestion, consult your doctor.
• Wear safety equipment, gloves and lenses.
• Try to keep the container tightly closed.
• Do not leave available to children.
• Prohibited from selling to minors.

The performance of the may vary depending on the porosity of the surface.
Porous substrates .................. 2 to 4 m2/litre
Low porosity substrates ......... 4 to 6 m2/litre

Not recommended for: Surfaces subjected to hydrostatic pressure, in continuous immersion of asphalt origin or materials that are not concrete, masonry or natural stone.

Saltillo Tile USA LLC. IT GUARANTEES THE USE OF HIGH QUALITY RAW MATERIALS AND STRICT PRODUCTION CONTROL. THE APPLICATION PROCESS IS RESPONSIBLE TO THE APPLICATOR. CONSULT OUR TECHNICAL DEPARTMENT.